Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Elgin Homeowners
A chimney that leaks, pulls poorly, or shows crumbling mortar at the crown won’t fix itself, and in an Elgin winter the freeze-thaw cycle makes every small opening worse. We handle the full job: we find out what’s wrong with a camera inspection and document it, then repair it with materials you can look up by name – DuraFlex liners, HeatShield restoration, Copperfield crowns – rather than anonymous hardware-store substitutes. Our technicians have up to 11 years of experience, and every finding is explained before any work is booked. One company handles the sweep, the inspection, and the repair, so you’re not chasing a second contractor to follow up on what the first one found. Call (877) 382-6902. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a stainless or powder-coated cap over the flue opening to keep rain, snow, birds, squirrels, and downdrafting wind out of the chimney. You need one when the flue has no cap at all, when the existing cap is a rusted single-wall piece, or when you’ve had animals or water in the firebox. We install Gelco and Famco caps sized to the flue, sealed at the crown, and matched to the appliance – a wood insert and an open fireplace don’t take the same cap. Typical installed cost runs $180 to $450 depending on flue count, cap style, and whether the crown needs attention first. It’s one of the smaller jobs on this list and one of the most effective at stopping water intrusion before it reaches the masonry.
Single-Flue and Multi-Flue Caps
Most fireplaces in Elgin have one flue; a chimney serving a furnace, water heater, and fireplace may have three. Multi-flue caps need a custom footprint so the lid clears every termination and still sheds water outward. We measure the actual crown, not the nominal flue size, which is where generic caps usually fail.
Cap Screens and Animal Guards
A cap without screening is an open door for nesting birds and squirrels, and nest material near the flue is a real fire concern. We fit stainless mesh screens rated for spark containment and sized so draft isn’t restricted. The screen is the part that usually outlasts the lid, so it’s worth getting right the first time.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is pulling a failed cap – rusted through, dented by a fallen limb, or sitting loose after wind – and installing a new one on a sound crown. Replacement makes sense when the old lid has holes, the screen is torn, or the cap no longer covers the flue after a relining job changed the termination height. We set the new Gelco or Famco cap with proper clearance and seal the base so water runs off the crown instead of behind the cap. Typical cost is $200 to $480 installed, with multi-flue and custom-built caps at the upper end. If the crown itself is cracked, that gets addressed first – a new cap on a failing crown just traps water underneath it.
Spotting a Cap That Has Failed
Rust streaks down the chimney face, a lid that rocks in wind, or water stains on the smoke chamber all point to a cap that’s no longer doing its job. Screen torn at one corner is enough to let a squirrel in. None of these are visible from the ground, which is why we check the top during every inspection.
Custom Caps for Odd Flue Layouts
Some Elgin homes have oversized masonry flues, off-center terminations, or a furnace flue sharing a crown with a fireplace. Those take a fabricated cap rather than a stock one. We build to the measured footprint so the lid overhangs correctly and the screens sit square on each opening.
Chimney Liner Installation
Chimney Liner Installation is fitting a new flue liner inside the existing chimney chase – a stainless flexible liner for a wood appliance, or an insulated liner when clearances are tight. You need it when the clay tile liner is cracked, spalled, or missing, when the chimney was built for an open fire and now serves an insert, or when a camera inspection shows gaps that let heat reach the framing. We install DuraFlex and Olympia Chimney systems, sized to the appliance and insulated where the manufacturer’s specifications call for it. Typical cost runs $2,200 to $5,800 depending on liner length, diameter, insulation, and whether the top plate and cap are included. This is the repair tier most sweep-only services hand off to someone else.
Why the Liner Is Not Optional
The liner is what keeps flue gases inside the chimney and heat away from wood framing, and a cracked clay tile does neither. An insert run without a correctly sized liner can also draft poorly and creosote up fast. This is where camera evidence matters: you see the crack on the monitor, and the recommendation follows from it.
Relining Around an Insert or Stove
Wood stoves and inserts need a liner sized to their outlet, not the original fireplace opening. We measure the appliance collar and the flue run before ordering, because an undersized liner is the most common cause of a smoking stove. The top plate, cap, and bottom connection all get sealed as part of the job.
Chimney Flashing Repair
Chimney Flashing Repair is the work of resealing or replacing the metal that bridges the gap where the chimney meets the roof – step flashing up the sides, and a head flashing at the top edge against the slope. It’s needed when you see water staining on the ceiling near the chimney, rusted or lifted flashing, or caulk that has cracked and pulled away. We remove the old sealant, reset or replace the flashing, and seal the counterflashing into the masonry. Typical cost runs $350 to $950 depending on roof pitch, access, and whether the flashing is being reset or fully rebuilt. Flashing is the single most common source of chimney leaks we find, and it gets missed when a sweep only looks down the flue.
Leaks That Aren’t the Cap
Plenty of “cap leaks” turn out to be flashing. Water runs in at the roof line on the uphill side, tracks along the framing, and shows up somewhere else entirely. When we find flashing as the cause, we say so and show you – and if it can wait, we tell you that too.
Chase Covers and Cricket Flashing
A chimney wider than about 30 inches on the uphill side needs a cricket to divert water around it, and many Elgin-area chimneys don’t have one. Where a cricket is missing, we can build one into the flashing repair. On factory chase covers, we reseal the seams and replace cracked panels.
Chimney Crown Repair
Chimney Crown Repair fixes the concrete cap on top of the chimney that sheds water away from the masonry below it. A crown cracks from freeze-thaw and from settling, and once water gets into the crack it migrates into the brick and the smoke chamber – the classic path to spalling brick and rusted damper. We remove loose material, rebuild the crown with a proper slope, and seal the bond at the flue. Typical cost is $450 to $1,100 depending on crown size and whether a portion of the top courses needs rebuilding first. Cracks wider than a hairline, or any crown with a puddle ring, is due.
Resurfacing Versus Rebuilding
A crown with surface crazing but no structural crack can often be resurfaced with a flexible coating over a prepared base. A crown that has broken away from the flue, or split through, gets rebuilt. We recommend based on what’s actually failing, not the calendar.
Slope and Overhang Matter
A correctly built crown slopes away from the flue and overhangs the masonry edge so water drips clear instead of running down the face. Rebuilding gives us the chance to get both right. It’s the detail that decides whether the crown lasts through a decade of Elgin winters.
Chimney Repair Companies
Chimney Repair Companies vary widely in what they’ll actually take on – some sweep and hand you a list, some subcontract the structural work, and a few do the whole job in-house. When you’re comparing chimney repair companies, ask what materials they stock and whether the crew that inspects is the crew that repairs. We handle the sweep, the inspection, and the repair, and our work draws from a defined set of chimney-industry brands: DuraFlex, Olympia Chimney, HeatShield, Gelco, Famco, and Copperfield. Typical repair jobs run $250 to $1,500 for the small-to-mid fixes, with relining and masonry rebuilds priced separately. The written estimate sets the final price, and we say plainly when a repair can safely wait another season.
Questions Worth Asking
Ask whether they’re insured and bonded, what brand of liner they install, and whether they photograph the inside of the flue. A company that can’t name the product going up the chimney is a company guessing. Ask, too, whether they charge for the estimate – ours is free.
Why Single-Company Accountability Matters
Splitting inspection from repair lets findings drift: the sweep flags a cracked crown, the mason says it’s the flashing, and nobody owns the leak. When one company does all of it, the diagnosis and the fix come from the same place. If we said it needed repair, we’re the ones who repair it.
Chimney Masonry Repair
Chimney Masonry Repair is the rebuilding and repointing of the brick, mortar joints, and structural work on the chimney body – tuckpointing spalled joints, replacing deteriorated brick, and rebuilding the top courses where freeze-thaw has popped the faces. It’s needed when joints have receded past the brick face, when brick faces are flaking (spalling), or when a lean or bow suggests the footing needs a look. We match mortar to the existing brick so the repair doesn’t trap moisture or set up a hard face against soft brick. Typical masonry repair runs $500 to $2,800 depending on how many courses are involved and whether there’s a rebuild. More than one Elgin chimney we’ve looked at needed repointing to stop water at the source, not a liner.
Repointing Versus Rebuilding
Repointing replaces the mortar joints and keeps the original brick; rebuilding takes the top section down and resets it. Repointing is the right choice when the brick faces are still sound. Once the faces are spalling, spot replacement is added to the repointing before the mortar goes back in.
Mortar That Matches the Brick
Soft old brick needs a soft, lime-rich mortar, and a hard modern mix will crack the brick faces within a few winters. We match the mortar to the brick, not to whatever’s on hand. That’s the difference between a repair that holds and one that creates the next job.
Brands We Service
We work with DuraFlex and Olympia Chimney liner systems, and we know where each one wears – at the top plate where the liner transitions to the cap, and at the appliance collar where heat cycles hardest. That’s the information that decides whether a liner can be resecured or whether it has to come out. We use HeatShield for liner restoration, a professional-grade repair that can rebuild a deteriorated clay flue without a full tear-out; not every sweep service carries it or has used it.
On the exterior side, we install Gelco and Famco chimney caps and covers, and Copperfield products for crown and masonry work – each chosen because the manufacturer’s specification actually matches the job. We don’t call ourselves a dealer and we don’t stock parts in a truck; we source the trade materials for the repair we’ve specified. Whether you have Olympia Chimney, DuraFlex, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Water stains or a white chalky bloom on the chimney face. The bloom (efflorescence) is salts pushed out as water moves through the brick, which means the crown, flashing, or joints are letting water in. Left alone, the next step is spalling brick.
- Crumbling mortar between the bricks or a flaking brick face. Recessed or sandy joints mean the masonry has lost its binder and can’t shed water. This is repointing territory, and it’s cheaper before a brick face pops.
- A smoky fireplace that pulls poorly on cold mornings. That can point to a blocked flue, a liner problem, or a chimney that’s undersized for the appliance. A camera inspection tells you which.
- A cracked or broken crown at the top of the chimney. A crack lets water straight into the masonry and the smoke chamber, and the freeze-thaw cycle widens it each winter. It’s a straightforward rebuild while it’s still just a crown.
- Creosote buildup, a smoky smell in the room, or a chimney fire in your memory. Heavy creosote near the flue top is the fuel for a chimney fire. A sweep and inspection settle whether anything structural has to follow.
Our Process, Step by Step
- 1
Sweep and camera inspection first. We run a sweep and then send a camera down the flue, so the diagnosis comes from what’s actually there. The photo report goes to you, and we walk through it before anyone talks about the repair.
- 2
Explain the findings and the options. We show you the crack, the spalled joint, the failed flashing, and lay out what each repair involves and what it costs. If a repair can wait a season, we say so, and we document that too.
- 3
Specify the materials. The repair gets specified by product: a DuraFlex or Olympia Chimney liner for a reline, HeatShield for a restoration, a Gelco or Famco cap, Copperfield crown and masonry work. The written estimate names what’s going in.
- 4
Book the repair and do the work. One company handles the sweep, the inspection, and the repair, so the crew that found the problem is the crew that fixes it. We confirm the price in writing before we start.
- 5
Final check and hand-off. We finish with a look at the repaired area and a plain explanation of what changed and what to watch. The documentation is yours to keep, and it’s what the next inspection gets compared to.
How Much Does Chimney Repair Cost in Elgin?
Chimney repair in Elgin generally runs from about $180 for a cap up to $5,800 or more for a full reline, and the written estimate sets the final price. A typical chimney cap installation runs $180 to $450 depending on flue count and cap style. A crown rebuild is $450 to $1,100, and flashing repair is $350 to $950 depending on roof pitch and access. Masonry repointing and spot brick replacement runs $500 to $2,800 by the number of courses. Liner installation is the largest line item at $2,200 to $5,800, with length, diameter, insulation, and the top plate all affecting the number. HeatShield restoration, where the clay flue is a candidate, is typically less than a full tear-out reline and gets quoted after the camera shows us the flue.
What affects the price: how much of the problem is the crown versus the masonry below it, whether the chimney is on a steep roof, how many flues share the crown, and whether the liner needs insulation to meet clearance. To avoid overpaying, ask for the camera evidence, the brand name of the material going in, and a written price before work starts. The free estimate includes the inspection findings, the photo report, and an itemized quote – and if part of the job can wait, we’ll say which part.
Our Service Area Near Elgin
We work out of Elgin and cover the Fox Valley towns around it: Algonquin, Lake in the Hills, Huntley, Hampshire, Fox River Grove, Barrington, Island Lake, Sycamore, Genoa, Woodstock, and Marengo. Travel time to the outer edge of that area is typically under an hour. For a nearby job, chimney repair in Algonquin works the same way: sweep, camera, written estimate. For towns further west, chimney repair in Lake in the Hills follows the same process.
Serving Elgin, IL – Our Local Coverage Area
We serve Elgin and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Elgin
Chimney repair is fixing the parts of the chimney system that have failed – the crown, the flashing, the masonry joints, the cap, or the flue liner. It’s different from a sweep, which is cleaning, and from an inspection, which is diagnosis. At Chimney Sweep Elgin, we do all three under one roof, so a repair follows the camera findings and nothing gets recommended that isn’t visible on the report. Call (877) 382-6902 for a free estimate.
Most small repairs – a cap, flashing, or a spot of repointing – are done in a single visit of a few hours. A crown rebuild is usually a day of work, and a full reline with an insulated DuraFlex or Olympia Chimney liner takes a day or two depending on access and flue length. Masonry rebuilding takes longer and we’ll tell you up front. Call (877) 382-6902 and we’ll size the job from the inspection.
Chimney repair in Elgin runs from about $180 for a chimney cap installation to $5,800 or more for a full reline, with crown and flashing work in the $350 to $1,100 range and masonry repointing $500 to $2,800. The written estimate sets the final price, and there’s no charge for the estimate itself. Call (877) 382-6902 for an exact quote – estimates are free.
Yes – we install DuraFlex and Olympia Chimney liner systems and can inspect, resecure, or replace those liners. We also use HeatShield for liner restoration, Gelco and Famco for caps, and Copperfield for crown and masonry work. Whether your chimney already has one of these or any other make, we can help. Call (877) 382-6902 to book an inspection.
Yes, same-day repair is often possible when the schedule allows. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday – we’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (877) 382-6902 to get on the schedule.
Repairs carry a workmanship guarantee plus whatever the manufacturer warrants on the materials – DuraFlex, Olympia Chimney, Gelco, Famco, Copperfield, and HeatShield each carry their own terms. We’ll tell you in writing which applies to your job before work starts. We don’t publish a single blanket figure, because the coverage follows the product and the repair. Call (877) 382-6902 to ask about your specific repair.
Clear the area around the fireplace and the hearth, and move anything breakable from the mantel. Make sure we have access to the roof side and the flue termination, and note any leaks, smells, or drafting issues you’ve noticed so we can check them. If you already have an inspection report from another company, have it on hand – it’s a useful starting point. Call (877) 382-6902 with any questions before we arrive.
Schedule Your Chimney Repair Service in Elgin Today
Whatever the crown, flashing, cap, or liner is doing, we can find it and fix it with materials you can look up. One company handles the sweep, the inspection, and the repair, and the written estimate is free and sets the final price. Call (877) 382-6902. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Elgin homeowners get a no-obligation estimate and a plain answer on what can wait and what can’t.
Written by the team at Chimney Sweep Elgin.